NEW GREAT WHITE 97 CuFt/60 Minute 4500 PSI CARBON FIBER SCBA Tank withDIN300 Valve
Not only are we well known in the Airgun community as having THE BEST Tanks and Fittings made in U. A, but also THE BEST Prices and THE BEST Service as well. We carry everything from Alpha to Omega, Compressors, Fittings, Hoses, Tanks etc. This is the largest 4500 PSI Carbon Fiber Tank available (It is called the Great White on our website). This particular tank is suited for Paintball, and Airgun applications. Carry Handle – For easy carrying. Feet – So the tank doesn’t roll off the table. Boot – So you can stand up the tank while filling your Airgun. Tank Protector – Necessary to prevent gouges, cuts etc. Tank Cylinder Specifications are below : Minimum Capacity = 550 Cu In Service Pressure = 4500 PSI Material = Carbon Fiber Nominal Diameter = 6.97 Nominal Length = 21.70 (Sans Valve) Maximum Weight = 11.5 Lbs. Valve Type = TJ3 Slo-Flo Valve with the following features. The TJ3 Slo-Flo Valve limits the flow out of the tank and into your airgun , thereby greatly decreasing the chances of over-filling your gun. We have designed the valve to fill a Marauder from 2000 PSI to 3000 PSI in approximately 10 seconds. The TJ3 Slo-Flo Valve will include a 40 inch MicroBore Hose that is rated 9,100 PSI working pressure over 30,000 PSI Burst! With STAINLESS STEEL Strain Relief and STAINLESS STEEL Foster Brand Quick Disconnects at each end. The MicroBore Hose is only 0.070 inch inside diameter, so no wasted air! The TJ3 Slo-Flo Valve will include an Integral Bleeder. The TJ3 Slo-Flo Valve will include a LARGE 2.5 STAINLESS STEEL Glycerin-Filled Output Gauge Made by Wika in U. I have hundreds of other size BRAND NEW 4500 PSI TANKS in stock. Either in Regulated, or Non-Regulated type. OWN A SHOEBOX COMPRESSOR? Want to fill your paintball tank or airgun directly from the Shoebox with the best setup available? Includes a very High Quality STAINLESS STEEL Bleeder, STAINLESS STEEL BAR/PSI Scale Liquid-Filled Gauge, pair of 40 inch long x 0.070 inch ID micro-bore hoses with STAINLESS STEEL Female Quick Disconnects on each end. DIN300 SCUBA HOSE ASSEMBLY. HIGHEST QUALITY STAINLESS STEEL (so the threads don’t wear) Hand-tight (no wrench needed) fitting, with our Highest Quality STAINLESS STEEL Bleeder, STAINLESS STEEL Glycerin Filled Gauge that reads BAR & PSI, 40 inch long x 0.070 inch ID micro-bore hose with strain relief at each end and STAINLESS STEEL “Foster” type quick fill on the end. This is a great replacement for hose those who currently have a 4500 PSI SCUBA tank. SCUBA Yoke HOSE ASSEMBLY. HIGHEST QUALITY Hand-tight (no wrench needed) SCUBA Yoke, with our Highest Quality STAINLESS STEEL Bleeder, STAINLESS STEEL 2.5″ Glycerin Filled Gauge that reads BAR & PSI, 40 inch long x 0.070 inch ID micro-bore hose, strain relief at each end and STAINLESS STEEL “Foster type quick fill on the end. HAVING TROUBLE FINDING A SOURCE OF 4500 PSI AIR FILLS? NITROGEN HOSE ASSEMBLIES MADE IN USA! Nitrogen tanks are readily available at most welding supply shops and they are cheap to rent! Also, they are 6000 PSI, so you get an amazing amount of fills. If you wish to fill your Carbon Fiber tank or air gun from a large Nitrogen tank, this is it. STAINLESS STEEL tank fitting, STAINLESS STEEL Glycerin Filled Gauge that reads BAR & PSI, Highest Quality STAINLESS STEEL Bleeder with easy to turn knob and 40″ x 0.070 inch ID micro-bore hose with strain relief at each end and STAINLESS STEEL “Foster type quick fill. REGULATED NITROGEN, SCBA, DIN300 HOSE ASSEMBLIES. A regulator can be added to any Hose Assembly I sell. Useful for filling airguns or paintball tanks from any type of tank. (You must specify the type of tank before purchasing as each is custom built to your specifications) Provides any pressure output from 0-5000 PSI, up to 6000 PSI Input. Excellent way to shoot your rifle from a bench while tethered to your air tank so that you have a constant fill pressure great for big bore rifles! Also fill your smaller air tank or air rifle from a large 6000 PSI tank more safely. Many other uses too! Now comes standard with 80 hose and my STAINLESS STEEL USA MADE Glycerin-Filled Gauges (shown in photo below). Items may appear slightly different, but function identically. For those that wish to fill their Airguns or paintball tanks from a Nitrogen tank, AND also use the regulator on their carbon fiber tank to safely fill or shoot from a tether. This system does both! CASCADE SETUP FOR 2 AIR TANKS MADE IN USA! Two 44 Cu Ft tanks can actually be better than one 88 Cu Ft tank when cascaded together with this system. SCBA shown on Left, SCUBA Yoke on right (also available in DIN300, and other fittings). Can also mix a SCUBA tank to bulk fill the airgun, and an SCBA to top it off. Note: I make this in such a way that you can cascade 2 airtanks, or use just 1 airtank if you were traveling, etc. With a simple quick disconnect. Upgrades for other Air Tanks. UPGRADE THE GAUGE ON YOUR CARBON FIBER TANK from the small hard to read gauge with BAR and MPa (shown on left) to a larger easier to read Glycerin Filled BAR and PSI (Shown on right). Now instead of guessing how many PSI you are putting in your tank, you will have an accurate and easier to read gauge from which you can directly read PSI. Be safe, and don’t miscalculate or guess in error. NOTE: THIS COMES STANDARD ON MY TANKS. UPGRADE THE HOSE ASSEMBLY ON YOUR CARBON FIBER TANK from the short hose to a 40 inch MicroBore hose with a STAINLESS STEEL strain relief at each end. Includes a STAINLESS STEEL Female Quick Disconnect. “THE WORKS” THE ULTIMATE UPGRADE HOSE ASSEMBLY FOR CARBON FIBER TANK Do you already own a tank with poor hose and under-rated fittings? Includes a 40 inch hose with a STAINLESS STEEL strain relief at each, a STAINLESS STEEL Foster Brand Female Quick Disconnect AND a REALLY NICE STAINLESS STEEL HAND TIGHT DIN300 (so no wrench required when filling, storing, or traveling with your tank). This DIN300 fitting looks like a piece of Jewelry! AIR TANK FILL ADAPTERS. If you prefer to fill your tank at a SCUBA shop that doesn’t have an SCBA adapter, we have them. Or, if you want to fill it at a place that fills paintball tanks, we have that adapter too (When used with our hose assembly). Note: All adapters are described from left side to right. Female STAINLESS STEEL DIN300 (SCUBA) to Hand Tight STAINLESS STEEL Female SCBA Fitting. For filling SCBA tanks at a SCUBA Dive Shop. STAINLESS STEEL Male Paintball (Foster brand PaintBall type) to Hand Tight STAINLESS STEEL SCBA Fitting. For filling SCBA tanks at places that fill paintball tanks MADE IN USA! STAINLESS STEEL Male Paintball (Foster type) to Hand Tight STAINLESS STEEL DIN300 SCUBA Fitting. For filling DIN300 Carbon Fiber tanks or DIN300 SCUBA tanks at places that fill paintball tanks. STAINLESS STEEL Male Paintball (Foster type) to Wrench Tight DIN300 SCUBA Fitting. Yoke (SCUBA Block) to Hand Tight STAINLESS STEEL SCBA Fitting. STAINLESS STEEL Fire House Adapter (aka STAINLESS STEEL Male SCBA Fitting) to Hand-Tight STAINLESS STEEL Male DIN300. No Wrench is needed! Good for two uses. 1 For using my high quality hoses with a DIN300 SCUBA tank, or 2 for filling DIN300 SCUBA tanks at a fire house. STAINLESS STEEL Fire House Adapter (aka STAINLESS STEEL Male SCBA Fitting) to Wrench-tight DIN300. Good for filling my (and other) Carbon Fiber and DIN300 SCUBA tanks at a fire house. Fire House Adapter to SCUBA Yoke = STAINLESS STEEL Male SCBA Fitting to SCUBA Yoke. Good for filling SCUBA tanks at a fire house. ALL STAINLESS STEEL Foster Brand Male Paintball to Male Paintball Fitting. For filling air tanks through the hose assembly. MADE IN USA, not Asian knock-offs. Note: for use only with my hose assemblies, many other hoses can’t handle the fill pressure since they are CO2 rated. STAINLESS STEEL 1/8 Male NPT to Male Paintball Quick Disconnect (Left). STAINLESS STEEL Female Paintball Quick Disconnect to 1/8 female NPT (right). STAINLESS STEEL Female Paintball Quick Disconnect to 1/8 Female NPT. STAINLESS STEEL Female Paintball Quick Disconnect to 1/8 Male NPT. STAINLESS STEEL Male Paintball Quick Disconnect to 1/8 Male NPT. MADE IN USA , not Asian knock-offs. STAINLESS STEEL 1/8 Female BSPP to Male Quick Disconnect with Dowdy Seal. Usually for use with Airgun probes. Fits Air Arms, FX, Webley, EdGun, newer etc. Male Paintball Quick Disconnect to 1/8 Female NPT. Dead Head (No, Not the Jerry Garcia type, the kind you put on the end of a SCUBA tank’s hose to determine your remaining tank pressure). (LEFT) 2.5″ STAINLESS STEEL, Glycerin-filled Gauge with PSI & BAR readout 1/4″ NPT. Also available to upgrade hand pumps Hill, FX, AirForce, etc. (RIGHT) STAINLESS STEEL 2.5 GAUGE with STAINLESS STEEL MALE QUICK DISCONNECT. READ THE PRESSURE OF YOUR SCUBA or SCBA TANK WITH THIS. If you bought one of my tanks, you don’t need this. But if you bought elsewhere and would like an accurate gauge that reads in BAR and PSI to easily measure the pressure inside your air tank, this is it. Just connect the male “Paintball/Foster” type Male Quick Disconnect to your air hose! STAINLESS STEEL and MADE IN USA! 1 (23mm) High Quality Metal Gauge with PSI readout. Excellent replacement for most air guns, Benjamin Marauder, FX, Daystate, etc. These are very nice gauges, not like paintball stuff. Also available in 1/8 BSPP or NPT back mount. The item “NEW GREAT WHITE 97 CuFt/60 Minute 4500 PSI CARBON FIBER SCBA Tank withDIN300 Valve” is in sale since Wednesday, July 30, 2014. This item is in the category “Sporting Goods\Outdoor Sports\Paintball\Air Systems & Accessories\N2 Tanks & Accessories”. The seller is “n6yyo” and is located in Santa Ana, California. This item can be shipped to United States.
- Brand: Carleton
- Model: 4500 PSI SCBA Tank
- MPN: P/N 6109
- Country/Region of Manufacture: United States
- GREAT WHITE 4500 PSI AIR TANK: BRAND NEW!